Glass Balustrade Fittings Explained: Spigots, Elbows, Connectors and End Caps
Share
Glass balustrade fittings are the metal parts that hold the glass, carry the handrail and fix the whole run to the floor. In our systems that means four groups: posts with glass clamps already fitted, handrail fittings (top spigots, elbows, connectors, wall connectors and end caps), base fixings for the posts, and gate hardware if you need an opening. This guide explains what each part does, where it goes and how to work out how many you need.
Every piece of metalwork in our range is 316 marine grade stainless steel in a brushed satin finish, so posts, clamps, handrail and fittings all match.
Posts and glass clamps
In our systems the 10mm toughened glass is held by clamps on 42.4mm stainless steel posts, rather than set into a channel in the floor. Posts arrive with the correct number of clamps already fitted, so you choose a post type for each position in your run:
- End post: two clamps, used at the start and finish of a run.
- Centre post: four clamps, holding a panel on each side in a straight line.
- Corner post: four clamps, for a 90 degree turn.
- Angle post: for corners that are not 90 degrees.
Each post takes 85mm of your total run, so the sum is simple: total run = (number of posts x 85mm) + (combined width of your glass panels). Our guide to measuring for a glass balustrade walks through it step by step.
Spare 316 glass clamps are available in square back or curved back profiles for 10mm glass, at £12 each. The square back sits flush against flat faces such as walls; the curved back is shaped for round tube. They suit both our handrail and no-handrail systems, and are useful as replacements, for a wall-mounted panel or for a non-standard run.
Handrail fittings explained
If you choose our glass balustrade system with handrail, a 42.4mm 316 handrail runs across the top of 980mm posts carrying 900mm glass. The rail comes in 1000mm, 1500mm, 2000mm and 2500mm lengths, is cut to length on site, and is joined and finished with these fittings:
| Fitting | What it does | Price each |
|---|---|---|
| Straight top spigot | Fixes the handrail to the top of a post on a straight run | £16 |
| 90 degree corner spigot | Fixes the handrail to the top of a corner post | £18 |
| Adjustable staircase spigot | Fixes the handrail to a post on a sloping stair run | £20 |
| 90 degree handrail elbow | Turns the rail through a right-angled corner | £15 |
| Adjustable handrail elbow | Turns the rail through non-standard angles and follows stair slopes | £22 |
| Straight handrail connector | Joins two lengths of rail into one continuous run | £13 |
| Handrail wall connector | Ends a run neatly into brickwork or masonry | £12 |
| Handrail end cap | Finishes any open end of rail | £8 |
Handrail fittings are secured with grub screws, tightened by hand once the full run is aligned. Dry-fit the whole run before you tighten anything, because it is much easier to check lengths and angles before the rail is fixed.
How many handrail fittings do you need?
A quick way to count them for a typical run:
- Top spigots: one for each post. Use a corner spigot on corner posts and staircase spigots on sloping sections.
- Elbows: one for each change of direction or change of slope.
- Straight connectors: one wherever two lengths of rail meet on a straight.
- Wall connectors: one wherever the rail stops against a wall.
- End caps: one for each free end of rail that does not finish at a wall.
If you are not planning a handrail, our frameless glass balustrade system uses 1100mm posts with 1000mm glass, so the glass finishes level with the top of the post and no rail fittings are needed. The two systems use different posts and glass heights and are not interchangeable.
Post fixings: anchoring to the floor
Base plate fixings are not included with posts, because the right fixing depends on what you are fixing into. Our balustrade post fixings cover the common cases:
- M10 x 100mm anchor bolts for concrete and brickwork, £15 for a pack of ten.
- M10 x 100mm hexagon head coach screws for timber decking and joists, £20 for a pack of ten. Always fix into a solid joist, never into decking boards alone.
- Drill bit and tap set for fabricating angle post fixings on site, £15.
Fix through every hole in the base plate, not just two, and check each post is plumb before final tightening. Base plates are 100mm diameter on 42.4mm tube.
Gate hardware
To add a gate to a glass run, our 316 glass gate hardware includes a pair of self closing hinges (£250) and a matching gate latch (£170), sold separately. Both suit 10mm glass, need no drilling and match the finish of the rest of the range. Most gates need one hinge pair and one latch. If the gate is for a pool, check any pool or child safety requirements that apply.
Fitting tips that protect the glass
- Tighten glass clamps by hand only. Never use power tools on clamps, as over-tightening can stress the panel.
- Leave the expansion gap between the glass edge and each clamp given in the product specification (4 to 15mm).
- Toughened glass cannot be cut, drilled or altered after toughening, so plan panel widths before you order. Panels come in 13 widths from 300mm to 1500mm in 100mm steps.
- Check each panel is square before the final tighten.
Quick checklist
- Decide between the handrail and no-handrail system.
- Measure the run and work out posts and panels using 85mm per post.
- Choose end, centre, corner or angle posts for each position.
- Count spigots, elbows, connectors, wall connectors and end caps if you have a handrail.
- Pick anchor bolts for concrete or brick, coach screws for timber joists.
- Add gate hinges and a latch if you need an opening.
- Check the height your project needs: 900mm for stairs and internal landings, 1100mm for external balconies and roof edges, with guarding usually needed where there is a drop of more than 600mm. See our UK height regulations guide.
Plan your balustrade
Not sure which fittings your layout needs? Send us your measurements through our glass balustrade designer and quote page and we will work out the posts, panels and fittings for your run. You can also browse the handrail system to see every fitting in one place.
Building regulations vary with the project. This guide is general information, not design advice. Always confirm your plans with your local building control body before you order.